Tourin Bars High Risers

Filter by manufacturer

Aprilia 98-03 RSV1000 Tourin Bars

These tig welded Stainless Steel replacement Tourin Bars relocate the end of the bars up 32mm , back 15mm and are 12mm wider , OEM brake line and cables can be retained , pre drilled and supplied with fitting instructions.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Aprilia

Part No. 299

More Information

Aprilia RST1000 Tourin Bars

These ali billet blocks spacer the OEM handle bars up by 15mm ,no modifications are required to the brake line or cables. Note: the forks must be extended through the triple clamps to the 3rd line ( 15mm) to enable fitment. If you are not already rideing with them in this position you will notice the bike will turn quicker with this new set up.

New Zealand WOF load test approved.

$325.00 NZD

Manufacturer. Aprilia

Part No. 497

More Information

Aprillia RSV1000 04-05 Factory & 06-09

These tig welded and polished 304SS Tourin Bars are 51mm to suit the Ohlins and the new model Showa front ends , they raise the end of the bar by 44mm are 12mm further back and 35mm wider , OEM cables and lines are retained and they are pre drilled for the switch block location pins.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Aprilia

Part No. 298

More Information

Aprillia RSV1000 04-05 Tourin Bars

Tig welded 316 Stainless steel , these replacement 52.8mm Tourin Bars will raise the end of the clip ons 44mm bring them back 12mm and are 35mm wider, OEM cables and lines can be retained .

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Aprilia

Part No. 297

More Information

BMW K1200gt 08 K1300gt 09-10 Tourin Bars

These Ali Billet Block Style Tourin Bars bring the handle bar position up 30mm and back 65mm closer to the rider, they come with fitting instructions and are straight forward to fit , no modifications are required to the cables etc.

New Zealand WOF load test approved.

$475.00 NZD

Manufacturer. BMW

Part No. 472

More Information

BMW R1100S Tourin Bars

These Stainless Steel Tourin Bars will raise your grips 40mm and bring them back 32mm. OEM brakeline and cables and bar ends and heated grips are retained. Fitting instructions provided. Customer evaluation available on request.

New Zealand WOF load test approved.

$549.00 NZD

Manufacturer. BMW

Part No. 218

More Information

Buell 1125R Tourin Bars

These stainless steel replacement Tourin Bars fit into the same position as the standard bards . They reposition the bars up 30mm and back 10mm (measured from the end of the bar as they are reangled) Standard brake line and all cables can be retained , fitting instructions provided. 5mm holes do need to be marked out and drilled for the switchblock and throttle. Rapid Art alloy bar ends are supplied for the hollow ends though threaded bosses can be fitted at your request or Buzzetti end weights to suit the hollow end can be supplied for an extra $20.

New Zealand WOF load test approved.

$375.00 NZD

Manufacturer. Buell

Part No. 518

More Information

Buell XB 9 / 12 Tourin Bars

These Stainless Steel bars fit into the factory cast clamps , they raise the end of the bar by 30mm are 10mm back towards the riser and are 20mm wider , some of the height is gained by re angling them 5 degrees flatter then the factory items the standard clutch cable and switch block wiring can be retained, a new longer- US Jurisdictional Compliance Standards Approved (WOF in NZ terms) BH braided brake line is supplied. They also come with Rapid Art anodised bar ends.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Buell

Part No. 99

More Information

Ducati 1000 Sport Classic Tourin Bars

Ducati Sport Classic High Rise Clip ons , Tig Welded fron Stainless Steel , these total replacement bars raise the end of the bar 60mm and bring them back 25mm and are 25mm wider ( measured from the end of the bar) all OEM cables and brake line can be retained .They are pre drilled for the switchblocks and full fitting instrcutions are provided. Note : the bars pictured are acually fitted to a GT as the customer wanted clip ons rather then the OEM coventional bars.Rapid Art alloy bar ends are provided for the open end bars,Buzzetti end weights can be supplied instead for and extra $20.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Ducati

Part No. 285

More Information

Ducati 1198 1098 848 Tourin Bars

Ducati 1198,1098 or 848 High rise clip ons Poilished 304 stainless steel for lasting good looks and strength , Raises the bar by 40mm , back 15mm and 20mm wider ( varies depending where you want to position them either higher and further away or closer to you and as low as 35mm higher) Pre drilled fro the switchblocks , standard brake and clutch line can be retained .

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Ducati

Part No. 363

More Information

Ducati 748,916,996 Tourin Bars

repositions bar end up by 38mm , back 20mm and 25mm wider , Standard hydralic lines and switch block wiring can be retained, supplied with ali billet mounts to reposition reservoirs and anodised ali bar ends , manufactured from polished 304 stainless steel.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Ducati

Part No. 210

More Information

Ducati 750 Sport Tourin Bars

Tig welded from 316 Stainless Steel , repositoning bars up 60mm , back 25 and 30mm wider

New Zealand WOF load test approved.

$429.00 NZD

Manufacturer. Ducati

Part No. 208

More Information

Ducati 800SS-1000DS Tourin Bars

These full replacement clip ons are maunfactured then polished from Stainless Steel. They are reangled and measured from the end of the bar will raise them 50mm bring them back 20mm and are 22mm wider . Standard brake line and cables can be retained they are pre drilled for the switch blocks and they are supplied with anodised alloy bar ends.Note : the steering lock must be reduced via the oem adjustments to fit these all explained in the fitting instructions.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Ducati

Part No. 328

More Information

Ducati 900/750SS 99-03 Tourin Bars

Fabricated and polished from 316 stainless steel, repositioning bars 60mm higher , 25mm back and 22mm wider fitting these clip ons requires no modifications to the brake line or cables.they are pre drilled for the switch blocks and come with full fitting instructions and anodised end plugs .

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Ducati

Part No. 209

More Information

Ducati ST2 ST4 Tourin Risers

These Billet Aluminium spacer blocks are slightly wedged to provide 25mm of rise at the end of the bar. They do not require any modifications to the brake/ clutch line or cables , they are supplied with the longer fasteners needed for fitment.

New Zealand WOF load test approved.

$365.00 NZD

Manufacturer. Ducati

Part No. 493

More Information

Ducati ST3 ST4 lower than oem bars

These Tourin Bars are actually about 30mm lower than the original bars to give a more sporty more attached feel to you rise. They come with anodised alloy bar ends but are not pre drilled for the switchblocks

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Ducati

Part No. 573

More Information

Honda CBR 1000RR 04-07 Tourin Bars

These Rapid Art High Risers are Tig welded then poished in 304 stainless steel. These bars will raise your grips 35mm higher, 20mm back towards you and are 30mm wider ( mearured from the end of the clip on .The OEM cables and brakeline can be retained along with the bar end weights. Fitting instructions provided.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Honda

Part No. 213

More Information

Honda CBR1000 95-99 Tourin Bars

Tig Welded from 316 Stainless Steel ,Relocates up 40mm back 25mm and 25mm wider, standard end weights,brake line and cables are retained

New Zealand WOF load test approved.

$429.00 NZD

Manufacturer. Honda

Part No. 122

More Information

Honda CBR1000RR 08-11 Tourin Bars

These Stainless 304 steel replacement high rise clip ons , measured from the end of the bar will raise your bars 40mm , 25mm back and 25mm wider each side. They come pre drilled for the switchblocks and are supplied with full fitting instructions, all standard cables and brake line as well and OEM end weights are retained.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Honda

Part No. 371

More Information

Honda CBR1100xx Blackbird 98-07 Tourin Bars

Tig welded then polished in 304 Stainless Steel , repositions bars 45mm higer - 30mm back - 30mm wider , standard brake lines, cables and end weights can be retained , they are pre drilled for the switch blocks and come with full fitting instructions.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Honda

Part No. 120

More Information

Honda CBR600F4i Tourin Bars

These Rapid Art High Rise Clip ons are manufactured from 304 Stainless Steel with a high polished finish. They will give you a 30mm rise measured from the end of the bar as they are re angled to 5 degrees , they also come back 15mm and are 25mm wider. Not available pre drilled for the switchblocks yet hence the 10% discount.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Honda

Part No. 461

More Information

Honda CBR600RR 03-04 Tourin Bars

These polished 304 stainless steel clip ons raise your bars up 30mm bring them back 25mm and are 25mm wider ,(measured from the end of the bar) no modifications are needed to the brake line or cables . They are supplied with full and straight forward fitting instructions and are pre drilled for the switchblocks.

New Zealand WOF load test approved.

$429.00 NZD

Manufacturer. Honda

Part No. 530

More Information

Honda CBR600RR 05-09 Tourin Bars

New Zealand WOF load test approved.

$429.00 NZD

Manufacturer. Honda

Part No. 349

More Information

Honda CBR900RR 96-99 Tourin Bars

TIG WELDED from 316 SS, Re angles bars to 5 degrees raises them 40mm , back 30mm and 30mm wider, standard end weights and cables can be retained .

New Zealand WOF load test approved.

$429.00 NZD

Manufacturer. Honda

Part No. 126

More Information

Honda CBR929 /954RR Tourin Bars

Tig welded and a polished finish in 304 Stainless steel , these Replacement High Rise Clip ons give a 30mm rise , 25mm back and 25mm wider ( measured from the end of the bar) The OEM brake , clucth line and wiring as well as the bar end weights are retained.Fitting instructions provided.

New Zealand WOF load test approved.

$429.00 NZD

Manufacturer. Honda

Part No. 347

More Information

Honda ST 1300 Tourin Bars

Fit beneath standard Clip On's to space them up by 30mm. No modifications required. Manufactured from 6061 Aluminium , Natural (silver) finish

New Zealand WOF load test approved.

$339.00 NZD

Manufacturer. Honda

Part No. 121

More Information

Honda VFR 800 02-09 Tourin Bars

These clip ons use a 25mm OD riser for extra rigidity (but still have the 22.2mm handle bar tube)as they are 45mm higher and 15mm back also 10mm wider than the factory items, they do clear the fairing and tank and the standard brake line , clutch and switch block wiring can be retained. Note: the mid rise option at 30mm higher is our most popular design this extra high was design specifically for a customer with a partcular injury who requested them as high is possible.

New Zealand WOF load test approved.

$449.00 NZD

Manufacturer. Honda

Part No. 127

More Information

Honda VFR1200 Tourin Bars

These High Rise Clip ons are manufactured in NZ from 304 stainless steel , tig welded and finished in a high polish ( bars pictured have been powder coated black for an extra $40 ) . They give a 15mm rise are 25mm back closer to the rider and are 10mm wider. They are pre drilled for the switchblocks and all the standard lines and cables are retained as are the oem end weights . They come with full fitting instructions .More pictures available on request.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Honda

Part No. 558

More Information

Honda VFR400 Tourin Bars

These High rise clip ons give a 55mm rise are 20mm back and 30mm wider . To fiot the you must have the top fairing mount cut and modifided as we have done to the bike pictured, you also need 2" longer throttle cables , the brake line and clutch cable can be retained.

New Zealand WOF load test approved.

$429.00 NZD

Manufacturer. Honda

Part No. 469

More Information

Honda VFR800 02-15 Mid-rise Tourin Bars

Mid Rise option our most popular height, Tig Welded then polished in 304 SS, raising them 30mmm , 10mm wider , no modifications required and standard end weights can be retained, these bars also allow the brake and clutch levers to be set at a slightly lower angle as the wide factory cast risers are very wide and restrict the position of the brake lever to a height which is unnatural to many riders.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Honda

Part No. 125

More Information

Honda VFR800 89-01 High-rise Tourin Bars

TIG WELDED FROM 316 SS, Re angles bars to 5 degrees raising them 30mm , back, 10mm and 10mm wider , no modifications required and standard end weights can be retained.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Honda

Part No. 124

More Information

Honda VTR1000 Firestorm Tourin Bars

Tig welded from 316 SS , Bars reangled to 5 degrees , raised by 25mm and back by 5mm ,12mm wider no modifications are required to fairing, standard bar end weights and cables can be retained note: extra 5mm height can be achieved if your happy with the switch block just fouling the fairing at full lock ( steering lock could be reduced to overcome this). NOTE: PLEASE LIST THE YEAR OF YOUR BIKE IN THE COMMENTS SECTION.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Honda

Part No. 123

More Information

Husqvarna Vitpilen 401 Tourin Bars

These full replacement high rise clip ons are machined and fabricated from 304 stainless steel. They give a 60mm rise and are 40mm back and 15mm wider than oem. They come pre drilled for the switchblocks and come with adaption sleeves so the oem end weights can be retained. Full fitting instructions provided. Picture shows Touring bar fitted on the right and oem bar still on left .

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Husqvarna

Part No. 582

More Information

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Kawasaki

Part No. 327

More Information

Kawasaki ZX6 98-02 Tourin Bars

Tig welded from 304 SS , repositons bars 15mm higher, 25mm back and 30mm wider,bars are reangled to 5 degrees , standard brake line, cables and end weight can be retained.Pre drilled for switchblocks. Full fitting instructions provided.

New Zealand WOF load test approved.

$429.00 NZD

Manufacturer. Kawasaki

Part No. 172

More Information

Kawasaki ZX6R 07-08 Tourin Bars

These polished Stainless Steel replacement clip ons raise the height of the bars (measured from the end) by 55mm and they are 30mm back and 30mm wider. Standard brake line , cables and bar ends can be retained. Pre drilled for the switchblocks and threaded bosses are welded in the ends so OEM bar ends can be retained, new brake fluid reservior mount provided. Full Fitting instructions also provided.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Kawasaki

Part No. 501

More Information

Kawasaki ZX9 98-03 Tourin Bars

These RapidArt High Risers are machined then tig welded and polished from 304 stainless steel. They will give you a 35mm rise measured from the end of the bars, they come back 25mm and are 25mm wider. All standard cables, brake lines and bar end weights are retained. At this stage you must mark out and drill the switch block location holes (hence the discounted price) as explained in the fitting instructions supplied.

New Zealand WOF load test approved.

$425.00 NZD

Manufacturer. Kawasaki

Part No. 454

More Information

Kawasaki ZZR 1100 Tourin Bars

Machined from 6061 Aluminium ,Anodised or polished finish, these spacers fit underneath the standard clip ons and raise them up 25mm, with no modifications needed to any cables.

New Zealand WOF load test approved.

$335.00 NZD

Manufacturer. Kawasaki

Part No. 217

More Information

Kawasaki ZZR 1200 Tourin Bars

Machined from 6061 Aluminium ,Anodised or polished finish, these spacers fit underneath the standard clip ons and raise them up 25mm with no modifications needed to the cables.

New Zealand WOF load test approved.

$335.00 NZD

Manufacturer. Kawasaki

Part No. 216

More Information

Moto Guzzi V7 Tourin Bars

These Tourin Bars are manufactured from 304 stainless steel and finished inn a high polish. They will give you a rise of 30mm measured at the end of the bar as they are reangled flater than the oem bars. They are pre drilled for the switch blocks and the oem bar ends are retained. All oem cables and brake line are retained. Fitting instructions provided.

New Zealand WOF load test approved.

$375.00 NZD

Manufacturer. Moto Guzzi

Part No. 540

More Information

Suzuki GS1200SS Tourin Bars

TIG WELDED then polished 304 Stainless Steel , RAISES Bars 45mm , back 25mm & 25mm wider , standard brake line and cables can be retained.Pre drillede for switchblock location supplied with full fitting instructions.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 46

More Information

Suzuki GSX600F Tourin Bars

These replacement clip ons are manufactured from Stainless Steel , they offer 25mm rise and 12mm back measured from the end of the bar, all standard lines and end weights can be retained .

New Zealand WOF load test approved.

$335.00 NZD

Manufacturer. Suzuki

Part No. 344

More Information

Suzuki GSX650F Tourin Risers

Suzuki GSX650F High Riser blocks, all standard cables apply, rises the bars by 30mm.

New Zealand WOF load test approved.

$249.00 NZD

Manufacturer. Suzuki

Part No. 486

More Information

Suzuki GSX750F Tourin Bars

These replacement clip ons are Tig welded from 304 Stainless Steel , they offer a 30mm rise are 20mm back and 15mm wider than the OEM items. they come with a riser block for the brake line so the standard brake line and all other cables can be retained .They are pre drilled fro the switch blocks and the standard end weights are also retained.

New Zealand WOF load test approved.

$365.00 NZD

Manufacturer. Suzuki

Part No. 433

More Information

Suzuki GSXR 1000 K1-K2 Tourin Bars

Tig welded from 316 Stainless steel , at 5 degrees angle these bars will raise your grips 50mm , bring them back 22mm towards you, and they will end up 25mm wider , standard cables ,brake line and end weights can be retained .Pre drilled for switchblocks.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 49

More Information

Suzuki GSXR 600 K3- K5 Tourin Bars

Tig welded stainless steel, these bars will raise your grips 40mm, take them 22mm back and 25mm wider.( measured from the end of the clip on) All standard cables and brakeline can be retained. Modified reseviour mount supplied along with full fitting instructions. Full fitting instructions provided. Note: these bars will need the switch block holes marked out and drilled.

New Zealand WOF load test approved.

$429.00 NZD

Manufacturer. Suzuki

Part No. 212

More Information

Suzuki GSXR 600 00-02 Tourin Bars

Tig welded from 316 Stainless Steel , Repositions bars up to 45mm higher- 20mm back - 25mm wider

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 219

More Information

Suzuki GSXR 600 750 K6-K9 Tourin Bars

These full replacement Stainless steel clip ons come in a high polished finish. They raise the bars by 40mm bring them back by 25mm and are 30mm wider. The OEM brake and clutchline and wiring as well as the bar ends are all retained.Full fitting instructions provided.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 485

More Information

Suzuki GSXR1000 K3-4 Tourin Bars

These replacement clip ons are manufactured from stainless steel then polished , they will raise the end of your clip on by 50mm , bring them back 20mm and are 25mm wider , all OEM brake lines and wiring can be retained as well as the end weights, they are pre drilled for the switch blocks and come with full fitting instructions.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 312

More Information

Suzuki GSXR1000 K5-K9 Tourin Bars

These custom made Stainless Steel full replacement Clip ons will re-position your bars up 44mm ,back 20mm and 25mm wider (measure from the end of the bar) Standard brake line and cables and end weights are retained and they are pre drilled for the switchblocks.Full fitting instructions and photos of the brake line re routing are provided. More photos can be e-mailed on request.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 311

More Information

Suzuki GSXR1000 L0- L3 Tourin Bars

These full replacement Tourin Bars are manufactured from 304 SS have a polished finish. They raise the bars by 50mm are 25mm wider and bring the bars back 25mm closer to the rider measured from the end of the clip on. OEM brake line , clutch cable ,wiring and bar ends are all retained and the full steering lock is not compromised, they are pre drilled for the switch blocks and are supplied with full fitting instructions and photos for the re routing of the brake line and switch block wiring. More photos available on request.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 517

More Information

Suzuki GSXR1100 1988 Tourin Bars

These stainless steel replacement clip ons are 30mm higher, 30mm back and 30mm wider than the standard items (measured from the end of the bar) they are reangled to 5 degrees , they are pre drilled for the switchblocks and the standard brake lines etc can be retained .

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 162

More Information

Suzuki GSXR1100 Tourin Bars

These Stainless Steel clip ons raise the end of the bar 50mm are 5mm back and 10mm wider , they use the OEM end weights are pre drilled for the switch blocks , and no modifications are needed to the brake line or cables.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 276

More Information

Suzuki GSXR1300 99-2011 Hayabusa Tourin Bars

These replacement high rise clip ons are manufactured and tig welded fron 304 stainless steel , they will raise you bars 30mm bring them back 25mm and are 15mm wider, they come pre drilled for the switchblocks and all cables and the brake line can be retained as well as the standard end weights. note: see GSX750F photo to get an idea of fitment.

New Zealand WOF load test approved.

$365.00 NZD

Manufacturer. Suzuki

Part No. 434

More Information

Suzuki GSXR600-750 L0-L3 Tourin Bars

These Rapid Art High Rise clip ons are manufactured in house from 304 Stainless Steel and are finished in a high polish. They give you a 50mm rise are 25mm back and 25mm wider this is achieved using a 5 degree drop . They do clear the fairings and tank and the OEM brake line can be retained as are all the other cables and wiring with some simple rerouting explained in the fitting instructions . They are pre drilled for the switchblocks and the standard end weights are retained.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 551

More Information

Suzuki Katana 1982 Tourin Bars

Tig welded from 316 Stainless Steel , attach underneath the triple clamp to provide upto 50mm rise

New Zealand WOF load test approved.

$429.00 NZD

Manufacturer. Suzuki

Part No. 222

More Information

Suzuki RF400/600/900 Tourin Bars

TIG WELDED from 316 Stainless Steel , these replacement bars will give you 30mm rise measured from the end of the bar and are 15mm back and 15mm wider , all standard lines and end weights can be retained .Do require a 5mm hole to be drilled in each bar for the switch block location pins.

New Zealand WOF load test approved.

$339.00 NZD

Manufacturer. Suzuki

Part No. 223

More Information

Suzuki SV 650 99-02 Tourin Bars

Tig welded from 304 Stainless Steel, repositions bars 50mm higher , 20mm back and 25mm wider , brake resiviour mount included, pre drilled for the switchblocks , supplied with full fitting instructions.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 45

More Information

Suzuki SV1000 02-08 Tourin Bars

Manufactured and polished from 304 Stainless steel, these replacement clip ons will raise your grips 40mm , move them 25mm towards you and they will end up 25mm wider, you can retain your standard brake lines , cables and bar end weights , they are pre drilled for the switch blocks and come with full fitting instructions.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 48

More Information

Suzuki SV650 03-2011 Tourin Bars

Tig Welded then polished in Stainless Steel , Repositions bars 45mm up,20mm back and 25mm wider, standard end weights can be retained as well as standard brake line & cables .Pre drilled for switchblocks , full fitting instructions.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 47

More Information

Suzuki TL1000R Tourin Bars

Tig welded from 304 Stainless Steel Repositions bars 35mm Higher - 20mm back - 25mm wider , Standard end weights , brake line and cables can be retained. Pre drilled for the switchblocks.Full fitting instructions provided.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 43

More Information

Suzuki TL1000S Tourin Bars

Tig welded from 316 Stainless Steel , repositons bars 50mm higher- 20mm back -25mm wider , standard end weights can be fitted, Standard brake line and cables can be retained , pre drilled for the switch blocks , full fitting instructions supplied.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Suzuki

Part No. 42

More Information

Triumph 675 daytona Extra high Tourin Bars

These are our latest version for the 675 Daytona they are welded from 304 stainless steel at a 0 degree drop and are 12mm higher at the riser so they can achieve a 65-70mm rise , 20mm back and 20mm wider ( depending on the position you fit them) For the abs model the oem brake line and all other cables are retained. For the Non asb model you will need to purchase a new brake line from us for an extra $135.00 The are pre drilled for the switch blocks and have the threads in the end for the oem bar ends. More photos available on request.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Triumph

Part No. 572

More Information

Triumph 675 Tourin Bars

These Polished stainless steel high rise clip, ons will give you a 35mm rise (measured from the end of the bar) 25mm back and 10mm wider. A new DOT approved braided brake line is supplied as the angle of the standard banjo fouls with the riser. All other cables and end weights can be retained. They are Pre drilled for the switchblocks. Full fitting provided.

New Zealand WOF load test approved.

$549.00 NZD

Manufacturer. Triumph

Part No. 348

More Information

Triumph 675R 2014 Tourin Bars

These Rapid Art high rise clip ons are manufactured from 304 stainless steel and finished in a high polish. They are re angled to 5 degrees these measurements are from the end of the bar 35mm higher , 25mm back and 10mm wider. They are pre drilled for the switch blocks the oem end plugs can be retained and full fitting instructions are provided. No modifications are required to the fairings and unlike the standard 675 the oem brake line can be retained.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Triumph

Part No. 556

More Information

Triumph RS /ST Tourin Risers

Aluminium Billet Risers which bolt underneath standard clip ons to raise height by 24mm. Cap screws included. No modifications required to cables.

New Zealand WOF load test approved.

$315.00 NZD

Manufacturer. Triumph

Part No. 78

More Information

Triumph T595 Tourin Bars

Tig welded from 304 Stainless Steel and finished in a high polish, Repositions bars 50mm higher and 15mm wider, reservoir mount built in (955 pictured -very similar to T595) Standard brake lines and cables can be retained ,pre drilled for the switchblocks, anodised Bar ends provided , Full fitting instructions supplied.

New Zealand WOF load test approved.

$429.00 NZD

Manufacturer. Triumph

Part No. 76

More Information

Triumph T955 Tourin Bars

Tig welded from 304 Stainless Steel and finished in a high polish, repositions bars 50mm higher and 15 mm wider, reservoir mount built in , requires no modifications to brake line or cables ,pre drilled for the switchblocks and full fitting instructions provided. Anodised alloy bar ends also included . note: a 13mm higher option is available but this set will require a longer brake line.

New Zealand WOF load test approved.

$429.00 NZD

Manufacturer. Triumph

Part No. 77

More Information

Triumph Thruxton Tourin Bars

Stainless Steel Tig Welded, raises bar 60mm higher, 25mm back, and 25mm wider. All standard cables and brakeline can be retained. New reservoir mount included pre-drilled for switch blocks, stainless steel headlight mounts must be cut down by 5mm, full instructions included.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Triumph

Part No. 79

More Information

Triumph Thruxton 1200 2016 Tourin Bars

These replacement High rise clip ons are fabricated from 304 stainless steel . They give a 40mm rise from standard. The come pre drilled for the switchblocks , the oem end weights / mirrors are retained and they can be used with the oem heated grips. A longer clutch cable off the Triumph Street twin must be purchased separately to be able to fit these. Full fitting instructions provided. These Tourin Bars also come in a 25mm higher option.

New Zealand WOF load test approved.

$499.00 NZD

Manufacturer. Triumph

Part No. 41

More Information

Truimph ST1050 2005-2006 Tourin Risers

These billet aluminium blocks mount betwwen the triple clamp and clip ons to give them a rise of 25mm, they are simple to fit and no modifications are required to the cables etc , fitting instructions included.

New Zealand WOF load test approved.

$395.00 NZD

Manufacturer. Triumph

Part No. 521

More Information

Yamaha FJ1200 Tourin Bars

These Stainless Steel full replacement high rise clip ons measured from the end of the clip on raise your bars by 25mm they are back 15mm and 13mm wider on each side . Pre drilled for the switch blocks and with all standard cables being retained they are simple to fit , supplied with fitting instructions and 300 gram end weights.

New Zealand WOF load test approved.

$399.00 NZD

Manufacturer. Yamaha

Part No. 370

More Information

Yamaha FJR1300 01-05 Tourin Risers

These aliuminium billet blocks raise the bars by 35mm, no modifications required to cables or the brake line. Longer cap screws and fitting instructions supplied.

New Zealand WOF load test approved.

$290.00 NZD

Manufacturer. Yamaha

Part No. 97

More Information

Yamaha R1 (98-01) Tourin Bars

Tig Welded from 316 Stainless Steel, Repositions bars 38mm higher , 40mm back and 20mm wider , standard end weights can be fitted , no modifications required to brake line or cables , pre drilled for the switchblocks ,supplied with ali bracket to reposition brake reservior and full fitting instructions.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Yamaha

Part No. 18

More Information

Yamaha R1 02-03 Tourin Bars

Tig Welded from 316 Stainless Steel , Repositions Bars 40mm Higher ,20mm back 25mm wider , standard end weights can be fitted ,no modifications required to the brake lines or cables ,supplied with ali bracket to remount brake reservior.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Yamaha

Part No. 19

More Information

Yamaha R1 07 Tourin Bars

Tig Welded and polished from Stainless Steel , these replacemnet High Rise Clip ons give a 40mm rise are 20mm back and 25mm wider , all standard cables , brake line and end weights can be retained , pre drilled , fitting instructions provided, replacement steering damper mounting clamp included.

New Zealand WOF load test approved.

$545.00 NZD

Manufacturer. Yamaha

Part No. 346

More Information

Yamaha R1 08-2011 Tourin Bars

These 304 Stainless Steel full replacement clip ons raise the bars by 35mm are 35mm back and 20mm wider measured from the end of the bar as they are re angled to 5 degrees. The standard brake line and cables are retained as are the end weights , they are pre drilled for the switch blocks and come with full fitting instructions.

New Zealand WOF load test approved.

$439.00 NZD

Manufacturer. Yamaha

Part No. 519

More Information

Yamaha R6 99-05 Tourin Bars

These full replacement Rapid Art High Rise clip ons are manufactured from Stainless steel, tig welded and polished. They give a 50mm rise are 15mm back and 20mm wider ( measured from the end of the bar) they are re angled to 5 degrees for more comfort and height. They are pre drilled for the switch blocks come with 180gm bar end weights and a mount for the barke fluid reservior. Full fitting instructions are provided.

New Zealand WOF load test approved.

$479.00 NZD

Manufacturer. Yamaha

Part No. 487

More Information

Yamaha YZF1000 Thundrerace Tourin Bars

Manufactured from 304 Stainless steel, these bars will relocate you grips up 50mm ,back towards you 30mm and are 30mm wider, you can retain your standard cables and brake lines , they are supplied with 300gm h/bar end weights,and the brkt required to re mount your brake reservoir. Full fitting instructions provied.

New Zealand WOF load test approved.

$475.00 NZD

Manufacturer. Yamaha

Part No. 9

More Information